|
When we set out to design the next generation of
growth regulators at Agro Nanotechnology Corp. we had
two objectives. The first was to create an environmentally
friendly product that would positively affect the growth
and health of a broad range of plants. The second
was to ensure that the product could be easily and
readily applied. When you use the product we hope you
will agree that we have achieved both objectives.
On this page you will find a general guide on how
to apply Nano-Gro™
to your plants. For more examples please download our
User Guide.*
1.
Allow
1 pellet of
Nano-Gro™
to dissolve passively in 1 liter (2
pints)
of water.
2.
Once
the pellet has dissolved entirely, shake the
solution in a vertical motion to mix the
solution thoroughly.
3.
Now
you have what we will refer to as the Working
Solution, or WS for short. The WS is good for 24
hours.
Keep
Nano-Gro™
and WS out of direct sunlight at all times 
 |
 |
|
With a seed dressing machine (Picture 1) or comparable equipment:
-
Dissolve 24 pellets of
Nano-Gro™
in 10 liters (10.5 quarts) of water per
ton of seeds
Exceptions:
Rapes: 12 pellets per 10 liters
(10.5 quarts)
Sunflowers: 10 pellets 10 liters
(10.5 quarts) |
| |
Picture 1
|
 |
 |
-
Soak seeds in the WS for 10 - 15 seconds
and plant as usual.
·
If seeds
are small and clump together when wet, dry
the seeds under shade for 12 - 24 hours. As
the seeds dry out they will begin to
separate and
are
ready to plant.
-
When the seedlings reach a stage of 2-3
real leaves apply 30 - 50 ml (1.0 – 1.7
fluid ounces) of WS per seedling
directly over the base of the plant.
Exceptions:
·
Squash
only requires a WS of 2 pellet per 1 liter
(2 pints)
of water. |
 |
 |
-
Soak seeds or bulbs
in WS for 25 seconds, but no longer than
1-minute and plant as usual.
-
If planting flower
clippings allow clippings to soak for a
minimum of 20 minutes or up to 30
minutes.
|
 |
 |
|
There are two
methods to apply
Nano-Gro™
to fruit trees:
·
Injection under bark
1.
Drill a hole
2.5 mm
(0.10" inch)
in diameter
91 cm (3
feet) above ground and
19 mm (¾" inch)
deep in the tree
2.
Within the aperture, inject 20 ml
(0.68 fluid
ounces)
of Nano-Gro™.
3.
Cover the aperture with a moist clump of
soil
·
Root application (mature tree)
1.
Dig a hole approximately
91 cm
(3
feet)
deep
30.5 cm (1 foot)
away from tree
2.
Pour 200 ml
(6.8 fluid
oz)
of the WS solution into the hole
3.
Cover hole |
This list is not intended to cover all possible applications
of Nano-Gro™. We
suggest you review our online
User
Guide or to visit our Contact
page to speak to a customer service representative about
your specific planting needs.
|
*
|
There are
a number plants not covered here or the
User Guide for which
Nano-Gro™
can be effectively used. Additionally, there
are several crop management programs that
may require applications different from
those listed here. This page serves to provide
examples of how
Nano-Gro™
may be used. For more guidance on how to
use the product for your crops please visit
our Contact page
to speak to a customer service representative
or contact your local distributor.
|
|
